Efforts to Control Potential Hazards of Working at Height at a Gresik Fertilizer Company, Indonesia
Downloads
Introduction: As one of the largest fertilizer industrieswith high competitiveness and high interest from consumers, the Gresik Fertilizer Company has various potential hazards that can cause workplace accidents, one of which is the danger of working at height. This study aims to determine the Occupational Safety and Health (OSH) programs and the application of hazard control of working at height in the Gresik Fertilizer Company. Methods: This study used a descriptive analysis method with a cross sectional study design. The variables studied were the hazard control efforts, the procedures to control the hazard, and the application of the hazard control process of working at height. Data collection techniques derived from secondary data in the form of company's documents, and the data analysis method used in this study was in the form of qualitative method. Results: the Gresik Fertilizer Companyhas several OSH programs for the control of hazard of working at height with a success rate of 90%, have control methods of working at height with a success rate of 90%, and have guidelines for working at height with a success rate of 85%. Conclusion: The Gresik fertilizer company has OSH programs to control working at height, has hazard control methods for working at height, and guidelines for working at height.
Keywords: control efforts, fertilizer company, working at height hazards
Ardina, S. A. (2012) Penerapan Safety Patrol Di PT. Toyota Motor Manufacturing Indonesia Karawang Plant. Undergraduate Thesis. Surakarta: Faculty of Medicine, Universitas Sebelas Maret.
Asriani, M., Hasyim, H., and Purba, I. (2011) ‘Faktor-Faktor Yang Berhubungan Dengan Perilaku Tidak Aman (Unsafe Act) di Bagian Pabrik Urea PT. Pupuk Sriwidjaja Palembang', Jurnal Ilmu Kesehatan Masyarakat, 2(2), pp. 103–109.
Barizqi, I. N. (2015) Hubungan Antara Kepatuhan Penggunaan APD Dengan Kejadian Kecelakaan Kerja Pada Pekerja Bangunan Pt . Adhi Karya Tbk Proyek Rumah Sakit Telogorejo Semarang. Undergraduate Thesis. Semarang: Faculty of Sport Science University of Negeri Semarang.
Bawang, J., Kawatu, P. A. T., and Wowor, R. (2018) ‘Analisis Potensi Bahaya Dengan Menggunakan Metode Job Safety Analysis Di Bagian Pengapalan Site Pakal PT. Aneka Tambang Tbk . UBPN Maluku Utara', Jurnal KESMAS, 7(5), pp. 1-13.
Candra, E. and Ruhyandi. (2008) ‘Faktor Faktor Yang Berhubungan Dengan Perilaku Kepatuhan Penggunaan APD Karyawan Bagian Press Shop di PT. Almasindo II Kabupaten Bandung Barat Tahun 2008', Jurnal Kesehatan Kartika Stikes A. Yani, pp. 29–44.
Cunningham, T. R. and Jacobson, C. J. (2018) ‘Safety Talk and Safety Culture: Discursive Repertoires as Indicators of Workplace Safety and Health Practice and Readiness to Change', Annals of Work Exposures and Health, 62(1), pp. 55–64.
Dyanita, F. (2018) ‘Kepatuhan Terhadap Sop Ketinggian Pada Pekerja Konstruksi', The Indonesian Journal of Occupational Safety and Health, 6(2), p. 225.
Gabriele (2018) ‘Analisis Penerapan Standar Operasional Prosedur (SOP) Di Departemen Marketing dan HRD PT. Cahaya Indo Persada', Agora, 6(1), pp. 1–10.
Hutajulu, R. A. R. (2018) Hubungan Tingkat Pengetahuan Penggunaan APD dengan Risiko Kecelakaan Kerja pada Pekerja di Unit Welding PT. Sumatera Maju Jaya Batam Tahun 2018. Undergraduate Thesis. Medan: Faculty of Public Health, University of Sumatera Utara.
Institute Health Science Stikes Cendekia Utama Kudus (2017) Prosiding HEFA (Health Events for All) Publikasi Hasil Riset Kesehatan untuk Daya Saing Bangsa. Kudus.
International Labour Organization (2013) ‘Keselamatan dan Kesehatan Kerja sarana untuk Produktivitas', in. Jakarta: International Labour Officee.
Khaqim, E. S. (2014) Analisis Sistem Ijin Kerja (SIKA) Terhadap Kejadian Kecelakaan Kerja Di Pt . Bakrie Construction Serang Banten. Undergraduate Thesis. Surakarta: Faculty Health Science, University of Muhammadiyah Surakarta.
Kurniawan, W., Setyaningsih, Y., and Wahyuni, I. (2013) ‘Hubungan Faktor Karakteristik Pekerja, Safety Morning Talk (SMT) dan HouseKeeping Dengan Kejadian Minor Injury Pada Pekerja di Proyek Pembangunan Gedung Kantor PT. X Jakarta', Journal of Chemical Information and Modeling, 5(3), pp. 323–331.
Ko, K.H., Student, G., and Lee, K.O. (2018) ‘Determining Efficient Safety Patrol Team Operations on Construction Sites', Journal of Engineering and Applied Sciences, 13(9), pp. 2732–2736.
Li, N. F. and Xiao, Z. (2018) ‘A Fire Drill Training System Based on VR and Kinect Somatosensory Technologies', International Journal of Online Engineering, 14(4), pp. 163–176.
Martalina, S., Yetti, H. and Lestari, Y. (2018) ‘Identifikasi Bahaya dan Risiko Keselamatan Kerja Pada Saat Overhaul di Area Kiln PT. X tahun 2017', Jurnal Kesehatan Andalas, 7(1), pp. 14–18.
Martiwi, R., Koesyanto, H. and Pawenang, T. (2017) ‘Faktor Penyebab Kecelakaan Kerja Pada Pembangunan Gedung', Higeia Journal of Public Health Research and Development, 1(4), pp. 61–71.
Minister of Manpower Regulation (1970) ‘No. 1 Tahun 1970 Tentang Keselamatan Kerja', Jakarta: Minister of Manpower Regulation.
Minister of Manpower Regulation (2009) ‘No. 36 Tahun 2009 Tentang Kesehatan', Jakarta: Minister of Manpower Regulation.
Mirnayanti, A and Prasetyo, E. (2017) Evaluasi Penerapan Job Safety Analysis (JSA) di Bagian Produksi Unit Paper Mill 7/8 PT. Pura Barutama, Prociding HEFA, pp. 24-29
Muhanafi, M. Y. (2015) Penerapan Hazard Identification, Risk Assesment and Determining Control Dalam Upaya Mengurangi Kecelakaan Kerja di PT Wijayakarya Beton PPB Majalengka. Undergraduate Thesis. Surakarta: Faculty of Health Science, University of Muhammadiyah Surakarta.
Mutwale-Ziko, J., Lushinga, N. and Akakandelwa, I. (2017) ‘An Evaluation of the Effectiveness of Health and Safety Induction Practices in the Zambian Construction Industry', International Journal of Health and Medical Engineering, 11(3), pp. 584–588.
Notoatmodjo, S. (2012) Metodelogi Penelitian Kesehatan. Jakarta: Rineka Cipta.
Nurjanah, J. A. (2012) Penerapan Hazard Identification Risk Assesment and Determining Control ( Hiradc ) Pada Pekerjaan Baru Sebagai Upaya Pencegahan Kecelakaan Kerja Di PT. Eastern Logistics Lamongan. Undergraduate Thesis. Surakarta: Faculty of Medicine, University of Sebelas Maret Surakarta.
Nurmianto, E., Anita, N. and Aulia, A. N. (2018) ‘Identifikasi Hazard Dan Perancangan Sistem Informasi Keselamatan Dan Kesehatan Kerja Di Unit Amoniak (Studi Kasus : PT. Petrokimia Gresik)', Jurnal Manajemen dan Teknik, 8(2), pp. 112–122.
Purnamasari, D. (2018) Penerapan Job Safety Analysis sebagai Upaya Pencegahan Kecelakaan Kerja di Bagian Pickled PT. Adi Satria Abadi Yogyakarta. Special Report. Surakarta: Faculty of Medicine, Universitas Sebelas Maret.
Regulations (2016) ‘No. 9 Tahun 2016 Tentang Keselamatan dan Kesehatan Kerja Dalam Pekerjaan di Ketinggian', Jakarta: Regulations.
Salmah, U. and Lubis, A. M. (2016) Sistem Permit to Work. Undergraduate Thesis. Medan: Faculty of Public Health, University of Sumatera Utara.
Sambada, G.H., Kurniawan, B., and Suroto. (2016) ‘Analisis Sistem Tanggap Darurat Kebakaran di Container Yard 02 Terminal Petikemas PT. Pelabuhan Indonesia III (Persero) Semarang Tahun 2016', Jurnal Kesehatan Masyarakat (e-Journal), 4(4), pp. 667–672.
Saputra, F. E. (2017) ‘Analisis Kesesuaian Penerapan Safety Sign Di PT. Terminal Petikemas Surabaya', The Indonesian Journal of Occupational Safety and Health, 5(2), p. 121.
Sari, L. M. (2010) Upaya Pencegahan dan Penanggulangan Potensi Bahaya Kebakaran di area outer tube casting pt. Kayaba Indonesia, Bekasi Jawa Barat. Undergraduate Thesis. Semarang: Faculty of Medicine, University of Sebelas Maret Surakarta.
Shofiana, I. (2015) Identifikasi Potensi Bahaya Pekerjaan Di Ketinggian Pada Proyek Pembangunan Gedung Parkiran Rumah Sakit Telogorejo (Studi Deskriptif Pada Proyek Konstruksi Oleh PT. Adhi Karya Semarang). Undergraduate Thesis. Semarang: Faculty of Sport Science, University of Negeri Semarang.
Sujono, R. (2018) Desain Alat Bantu Keselamatan dan Kegiatan Kerja Petani Cengkeh dengan Pendekatan User Centered Design. Undergraduate Thesis. Jogjakarta: Faculty of Industrial Technology, University of Islam Indonesia.
Syahputra, M.R. and Sulaksmono, M. (2014) ‘Kelengkapan Pemenuhan Syarat Operator Ketel Uap Dengan Upaya Pengoperasian Dan Pemeliharaan Di PT. Pupuk Kaltim (Studi Pada Operator Di Industri Kimia)', The Indonesian Journal of Occupational Safety and Health, 3(2), pp. 201–211.
Talab, A.H.D., and Azari, G. R. (2017) ‘Safety Sign Perception and Adoption with the ISO and ANSI Standards', Jundishapur Journal of Health Science, 9(4), pp. 1–6.
Wahyuadi, H. T. (2016) ‘Analisis Implementasi Izin Kerja Di Ketinggian Terhadap Kecelakaan Kerja Di PT. X', Jurnal Kesehatan Masyarakat (e-Journal), 3.
In order to be accepted and published by The Indonesian Journal of Occupational Safety and Health, Author(s) who submit an article should complete all the review process. The copyright of received articles assigned to the The Indonesian Journal of Occupational Safety and Health and Department of Safety and Health, Universitas Airlangga as publishers of the journal. The intended copyright includes the rights to publish articles in various forms (including reprints).
The Editorial Team of The Indonesian Journal Of Occupational Safety and Health and Department of Safety and Health strive to ensure that no errors occur in the articles that have been published, both data errors and statements in the article.
Users of this website will be licensed to use materials from this website following the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. No fees charged. Please use the materials accordingly.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Attribution ” You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
NonCommercial ” You may not use the material for commercial purposes.
ShareAlike ” If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.
How to Submit Articles in OJS
