Proposed Workstation Design in Laboratory for Musculoskeletal Disorder Complaints
Downloads
Introduction:Laboratory is a means of improving the effectiveness of learning. The problem faced by laboratory staff in performing their work (analysis and experimentation) is fatigue caused by long work time with inappropriate sitting posture and position. The use of a wooden chair without a backrest and with a seat height that is too high or too low can cause musculoskeletal disorders (MSDs). This study aims to provide a workstation design suggestion with attention to ergonomics to reduce complaints of musculoskeletal disorders. Method: This descriptive research used an observational method. The population in this research consisted of 31 female students of a feed laboratory user, and the sample consisted of 16 respondents at the SIKIA Laboratory. Data collection for this study was conducted from July to September 2022. The independent variable in this study was the dimension of the workstation, and the dependent variable was musculoskeletal complaints. Result: Anthropometric measurements on laboratory assistants of the SIKIA Laboratory showed that the average popliteal height was 53.25 cm. Assessment on musculoskeletal disorder complaints shows that most complaints are found on "Pain in the back” with a score of 36. A new chair and table design is proposed, where the width of the seat back is 39.75 cm. Conclusion: A new workstation design is proposed that focuses on ergonomics to reduce the complaints of musculoskeletal disorders.
Aprillina, F. et al. (2019) ‘Perancangan Meja Dan Kursi Ergonomis Sebagai Fasilitas Gaming', Jurnal Intra, 7(2), pp. 775–780.
Aras, A. F, Rahmatika, D., and Putra, E. (2019) ‘Perancangan Meja Laptop Portable Yang Ergonomis Untuk Penyandang Cerebral Palsy Dengan Pendekatan Antropometri', Jurnal Inovator, 2(1), pp. 16–19.
Denaneer, T., Tanzila, R.A. and Rachmadianty, M. (2022) ‘Hubungan Ergonomisitas Kursi Dengan Keluhan Muskuloskeletal Pada Pekerja Di Perusahaan X Di Jambi', OKUPASI: Scientific Journal of Occupational Safety & Health, 2(1), pp. 34–42.
Dinar, A. et al. (2018) ‘Analysis Of Ergonomic Risk Factors In Relation To Musculoskeletal Disorder Symptoms In Office Workers', Kne Life Sciences, 4(5), pp. 16-29.
Djaali, N.A. (2019) ‘Analisis Keluhan Musculoskeletal Disorders (Msds) Pada Karyawan Pt. Control System Arena Para Nusa', Jurnal Ilmiah Kesehatan, 11(1), pp. 80–87.
Emda, A. (2017) ‘Laboratorium Sebagai Sarana Pembelajaran Kimia Dalam Meningkatkan Pengetahuan Dan Ketrampilan Kerja Ilmiah Amna', Journal Lantanida, 5(1), pp. 83–92.
Fatimah, S. and Indrawati, F. (2018) ‘Program Keselamatan Dan Kesehatan Kerja Di Laboratorium Kimia', Higeia Journal Of Public Health Research And Development, 1(3), pp. 84–94.
Fitra, F., Desyanti, D. and Suhaidi, M. (2020) ‘Penerapan Data Antropometri Siswa Dalam Perancangan Tempat Berwhudu Di SdIT Ath Thaariq - 2 Dumai', J-Abdipamas (Jurnal Pengabdian Kepada Masyarakat), 4(1), pp. 1-10.
Fitri, M., Adelino, M.I. and Putra, F.A. (2021) ‘Proposed Design Of Ergonomic Chair Plus Table With Anthropometry Approach Meldia', Menara Ilmu, Xv(01), pp. 71–76.
Gunawan, I. (2019) ‘Managemen Pengelolaan Alat Dan Bahan Di Laboratorium Mikrobiologi', Jurnal Pengelolaan Laboratorium Pendidikan, 1(1), pp. 19-25.
Himarosa, R.A. (2019) ‘Evaluasi Ketidakcocokan Ukuran Kursi Kuliah Pada Perguruan Tinggi', JMPM (Jurnal Material Dan Proses Manufaktur), 3(2), pp. 106–115.
Jaelani, I.M., Muslimin, M. And Efendi, I.B. (2022) ‘Analisis Risiko Work-Related Musculoskeletal Disorders Berdasarkan Postur Kerja Pada Pekerja Industri Sandal Handmade ( Studi Kasus Di UD. Yuriko Indonesia )', Prosiding Semastek, 1(1), pp. 249–258.
Kautsar, F. And Dewi, N.K. (2020) ‘Kursi Kerja Ergonomis PT XYZ', Journal Of Industrial View, 2(2), Pp. 36–44.
Kusuma, O. P., Ahya, R, and Darsini, D. (2020) ‘Perancangan Meja Kursi Porting Dengan Konsep Ergonomi Guna Memperbaiki Postur Kerja', Japti: Jurnal Aplikasi Ilmu Teknik Industri, 1(September), pp. 58–66.
Mesra, T. (2017) ‘Kursi Kerja Ergonomis Operator Bagging Pupuk Trisna', Prosiding Semnas Teknik, 1(1), pp. 7–13.
Muis, A.A. et al. (2022) ‘Rancangan Meja Pengatur Ketinggian Otomatis Menggunakan Pendekatan Antropometri Dengan Metode Quality Function Deployment (QFD)', Jurnal Teknologi Dan Manajemen Industri Terapan, 1(Ii), pp. 114–122.
Noviarmi, F.S.I. and Ningtiyas, M.K. (2018) ‘Design Of Operator Station Work On Line Packing PT. X Surabaya', Journal Of Industrial Hygiene And Occupational Health, 2(2), P. 112.
Qurthuby, M (2019) ‘Usulan Desain Meja Komputer Dengan Metode Quality Function Deployment (QFD)', Seminar Dan Konferensi Nasional Idec [Preprint].
Puspitasari, I. and Wibowo, R. K. K. (2017) ‘Modifikasi Kursi Penumpang Kereta Api Ekonomi Yang Ergonomis Dengan Metode Ergonomic Function Deployment(Studi Kasus Pada Ka Logawa Yang Diproduksi Di PT. Inka)', Jurnal ROTOR, 9(1), pp. 29-34.
Rahdiana, N. (2018) ‘Identifikasi Risiko Ergonomi Operator Mesin Potong Guillotine Dengan Metode Nordic Body Map (Studi Kasus Di PT. XZY)', Industry Xplore, 2(1), pp. 1–12.
Rosanti, E. and Wulandari. D. (2018) ‘Pengaruh Perbaikan Kursi Kerja Terhadap Keluhan Muskuloskeletal Pada Pekerjaan Menjahit Di Desa X', Journal Of Industrial Hygiene And Occupational Health, 1(1), Pp. 23–29.
Santosa, A. and Ariska, D.K. (2018) ‘Faktor-Faktor Yang Berhubungan Dengan Kejadian Musculoskeletal Disorders Pada Pekerja Batik Di Kecamatan Sokaraja Banyumas', Jurnal Ilmiah Ilmu-Ilmu Kesehatan, 16(1), Pp. 42–46.
Setyaningsih, L. (2019) ‘Perancangan Footrest Untuk Mengurangi Kelelahan Operator Pada Bagian Kaki Di Cell S/A Coil Xs156 Di PT.ABC', Jurnal Pasti, X(2), pp. 126–137.
Sinaga, H.H., Siboro, B.A.H. and Marbun, C.E. (2021) ‘Desain Meja Dan Kursi Tutorial Laboratorium Desain Produk Dan Inovasi Menggunakan Metode 12 Prinsip Ergonomi Dan Pendekatan Antropometri', Jurnal Sistem Teknik Industri, 23(1), pp. 34–45.
Sokhibi, A. (2017) ‘Perancangan Kursi Ergonomis Untuk Memperbaiki Posisi Kerja Pada Proses Packaging Jenang Kudus', Jurnal Rekayasa Sistem Industri, 3(1), pp. 61–72.
Suryatman, T. H. (2019) ‘Desain Kursi Santai Multifungsi Ergonomis Dengan Menggunakan Pendekatan Antropometri', Journal Industrial Manufacturing, 4(1), pp. 45–54.
Soewarno, A. (2017) ‘Perbaikan Lingkungan Kerja Pada Pengrajin Ukiran Kelongsong Peluru Dengan Menyesuaikan Tinggi Meja Kerja', Jurnal Permukiman Natah, 3(2), pp. 62–101.
Tjahayuningtyas, A. (2019) ‘Faktor Yang Mempengaruhi Keluhan Musculoskeletal Disorders ( Msds ) Pada Pekerja Informal Factors Affecting Musculoskeletal Disorders (MSDs)', The Indonesian Journal of Occupational Safety and Health, 8(1), pp. 1–10.
Wibowo, D. P. (2012) Perancangan Ulang Desain Kursi Penumpang Mobil Land Rover Yang Ergonomis Dengan Metode Ergonomic Function Deployment (EFD). Thesis. Yogyakarta: Faculty of Industrial Technology Universitas UPN Yogyakarta.
Windari, A. et al. (2018) ‘Tinjauan Aspek Ergonomi Berdasarkan Antropometri Petugas Filing Terhadap Keselamatan Dan Kesehatan Kerja (K3) Petugas', Jurnal Rekam Medis Dan Informasi Kesehatan, 1(2), pp. 81-87.
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
In order to be accepted and published by The Indonesian Journal of Occupational Safety and Health, Author(s) who submit an article should complete all the review process. The copyright of received articles assigned to the The Indonesian Journal of Occupational Safety and Health and Department of Safety and Health, Universitas Airlangga as publishers of the journal. The intended copyright includes the rights to publish articles in various forms (including reprints).
The Editorial Team of The Indonesian Journal Of Occupational Safety and Health and Department of Safety and Health strive to ensure that no errors occur in the articles that have been published, both data errors and statements in the article.
Users of this website will be licensed to use materials from this website following the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. No fees charged. Please use the materials accordingly.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Attribution ” You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
NonCommercial ” You may not use the material for commercial purposes.
ShareAlike ” If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.
How to Submit Articles in OJS
